If you've lost your Subaru car key, you should call a locksmith. Locksmiths can usually cut you a key for less than the dealer.
Fob remote "push to start" intelligent keys or a basic metal key are the two main kinds of subaru forester key replacement car keys. The Fob key needs to have its chip reprogrammed.
Keyless Entry System
A key fob lets you to lock or unlock your Subaru from a distance and could even unlock the trunk or lift gate of your vehicle. These remotes make use of the keypad of your car to connect to your vehicle's computer.
Certain models of Subaru offer a little-known feature called PIN Code Access. You can utilize a personalized number sequence to start and open your vehicle. Refer to the owner's manual for learn how to use this feature if you have a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.
It's possible that the battery inside the key fob is dying. The first thing to do is make sure that the key fob has new batteries, and you can do this using a handheld remote tester or a basic multimeter that you can find in your garage at home.
Next, you'll want to take the key fob out of its case and inspect its transmitter circuit board. The board will contain one or two sets of eight-digit numbers, so write down the first set so that you can remember it later. After that you can put the key fob back together and you'll be able to begin programming it at home. The procedure for programming varies depending on the model and year of your vehicle but it's usually easy enough to complete on your own.
Key Fobs
Subaru's newest models are all equipped with key fobs that don't just unlock your doors however, they also activate your lights, lock your gas cap, and start your car. This last trick is particularly useful if you've been at a gas station and your car wouldn't even start because the battery in the key fob has failed.
If your subaru key fob is brand new or old you can be sure that the key fob can be replaced with little difficulty. Remember that some of the modern models, with their advanced technology, may require a visit to the dealer. With little effort and some time, you can make your own replacement key fob.
Begin by opening the case and examining the circuit board of the transmitter. (Instructions on how to open the case are usually found in the owner's manual). There should be two or more serial numbers with 8 digits each. Note down the first number in the series and keep it handy to refer to later on.
Next, climb into the driver's seat. Close all the doors. Turn the key 10 times to start your car, and then switch off the engine. Press the lock button on your key fob and then open the door to ensure that your doors are functioning properly. Close the door, then remove the key. The chime should be heard from your vehicle, signaling that the key fob is programmed.
Ignition System
The key battery may be dead if your Subaru keys aren't working as they should. You can replace the battery in your key fob by yourself if know how. Battery replacement is affordable and easy to find. If your key fob doesn't respond to your commands, it could be another problem. It's recommended to visit a dealer to get an extra key. They will make sure that the key is genuine Subaru key, that is in warranty, and that it is programmed to your vehicle. This is a lot easier and safer than buying an aftermarket key from a website.
You can also request that the dealer cut a brand new key if you supply them with your VIN and subaru car Key evidence of ownership. They'll use this information to create a code for the replacement key to ensure that it will be accepted by your immobilizer. This procedure is more complicated than cutting a new one, and dealers will typically charge a higher price for this service.
Once the new key is programmed and you're able to swap it with your current key. You'll have only five seconds to insert the second key, which is why it's important to keep an active key in your bag. Once the security light ceases to flash and you're able to remove the new key and test it to make sure it's functioning properly.
Battery Replacement
Subaru fobs are extremely useful because they can turn on the sunroof and power windows in your car with just one button press. The battery in your Subaru fob isn't designed to last forever, and it will require replacement at some point. Fortunately, changing the battery is a straightforward process that you can complete yourself with the help of this short guide from Capitol Subaru.
To begin, you'll need to locate the small crevice within the seam that divides the back and front of your key fob. Using a small flathead screwdriver, you can break this seam wide to reveal a small compartment that houses the battery. Remove the old battery and then replace it with a fresh one, making sure that it is facing the right side up. After you have put everything together and you are ready to use the new key fob for locking in, unlocking, and even starting your vehicle.
It's always best to have an extra set of keys on hand in case you've lost one or not functioning properly. A new key can easily be purchased at your local dealership for cars or you can request one made by a locksmith. It is important to ensure that your key fob is working correctly as soon as you can so that you can safely drive.
